the global timeout if set. Also, as was reported in the bug report #2956437
by Ryan Chan, the time stamp to use as basis for the per command timeout was
not set properly in the DONE phase for FTP (and not for SMTP) so I fixed
that just now. This was a regression compared to 7.19.7 due to the
conversion of FTP code over to the generic pingpong concepts.
http://curl.haxx.se/bug/view.cgi?id=2956437
again when downloading files over FTP using ASCII and it turns out that the
final size of the file is not the same as the initial size the server
reported. This is very common since servers don't take the newline
conversions into account.
command is a special "hack" used by the drftpd server, but even though it is
a custom extension I've deemed it fine to add to libcurl since this server
seems to survive and people keep using it and want libcurl to support
it. The new libcurl option is named CURLOPT_FTP_USE_PRET, and it is also
usable from the curl tool with --ftp-pret. Using this option on a server
that doesn't support this command will make libcurl fail.
meter/callback during FTP command/response sequences. It turned out it was
really lame before and now the progress meter SHOULD get called at least
once per second.
used during the FTP connection phase (after the actual TCP connect), while
it of course should be. I also made the speed check get called correctly so
that really slow servers will trigger that properly too.
QUOTE commands and the request used the same path as the connection had
already changed to, it would decide that no commands would be necessary for
the "DO" action and that was not handled properly but libcurl would instead
hang.
CURLOPT_PREQUOTE) now accept a preceeding asterisk before the command to
send when using FTP, as a sign that libcurl shall simply ignore the response
from the server instead of treating it as an error. Not treating a 400+ FTP
response code as an error means that failed commands will not abort the
chain of commands, nor will they cause the connection to get disconnected.
to use the "standard" ENABLE_IPV6 one. Also, if port number cannot be figured
out to connect to after a name resolve (due to it not being IPv4 or IPv6),
that particular address will now simply be skipped.
With the curl memory tracking feature decoupled from the debug build feature,
CURLDEBUG and DEBUGBUILD preprocessor symbol definitions are used as follows:
CURLDEBUG used for curl debug memory tracking specific code (--enable-curldebug)
DEBUGBUILD used for debug enabled specific code (--enable-debug)
Chen pointed out how curl couldn't upload with resume when reading from a
pipe.
This ended up with the introduction of a new return code for the
CURLOPT_SEEKFUNCTION callback that basically says that the seek failed but
that libcurl may try to resolve the situation anyway. In our case this means
libcurl will attempt to instead read that much data from the stream instead
of seeking and that way curl can now upload with resume when data is read
from a stream!
how it occurs (http://curl.haxx.se/mail/lib-2009-04/0289.html). The
conclusion was that if an error is detected and Curl_done() is called for
the connection, ftp_done() could at times return another error code that
then would take precedence and that new code confused existing logic that
works for the first error code (CURLE_SEND_ERROR) only.
proxy. libcurl would then wrongly close the connection after each
request. In his case it had the weird side-effect that it killed NTLM auth
for the proxy causing an inifinite loop!
I added test case 1098 to verify this fix. The test case does however not
properly verify that the transfers are done persistently - as I couldn't
think of a clever way to achieve it right now - but you need to read the
stderr output after a test run to see that it truly did the right thing.
FTP with the multi interface: when a transfer fails, like when aborted by a
write callback, the control connection was wrongly closed and thus not
re-used properly.
This change is also an attempt to cleanup the code somewhat in this area, as
now the FTP code attempts to keep (better) track on pending responses
necessary to get read in ftp_done().
plain FTP connections, and it will then allow MKD to fail once and retry the
CWD afterwards. This is especially useful if you're doing many simultanoes
connections against the same server and they all have this option enabled,
as then CWD may first fail but then another connection does MKD before this
connection and thus MKD fails but trying CWD works! The numbers can
(should?) now be set with the convenience enums now called
CURLFTP_CREATE_DIR and CURLFTP_CREATE_DIR_RETRY.
Tests has proven that if you're making an application that uploads a set of
files to an ftp server, you will get a noticable gain in speed if you're
using multiple connections and this option will be then be very useful.
the condition in the previous request was unmet. This is typically a time
condition set with CURLOPT_TIMECONDITION and was previously not possible to
reliably figure out. From bug report #2565128
(http://curl.haxx.se/bug/view.cgi?id=2565128)
