Setting bit 2 for this value was documented as having a constant value
defined as CURL_REDIR_POST_303 yet referenced a 302 request.
Additionally corrected the meaning of CURL_REDIR_POST_ALL for all three
bits and fixed problems with the bolding of keywords in this section.
Standardised how RFCs are referenced so that the website may autolink to
the correct documentation on ietf.org. Additionally removed the one link
to RFC3986 on curl.haxx.se.
If an empty string is passed to CURLOPT_SSH_PUBLIC_KEYFILE, libcurl will
pass no public key to libssh2 which then tries to compute it from the
private key. This is known to work when libssh2 1.4.0+ is linked against
OpenSSL.
Added information relating to the new CURLOPT_MAIL_AUTH parameter and
reworked CURLOPT_MAIL_FROM and CURLOPT_MAIL_RCPT to be a clearer.
Fixed inconsistencies of "vocalisation of the abbreviation" versus
"vocalisation of the first word" for all abbreviations.
Corrected a typo in CURLOPT_NOPROXY.
Allow an appliction to set libcurl specific SSL options. The first and
only options supported right now is CURLSSLOPT_ALLOW_BEAST.
It will make libcurl to disable any work-arounds the underlying SSL
library may have to address a known security flaw in the SSL3 and TLS1.0
protocol versions.
This is a reaction to us unconditionally removing that behavior after
this security advisory:
http://curl.haxx.se/docs/adv_20120124B.html
... it did however cause a lot of programs to fail because of old
servers not liking this work-around. Now programs can opt to decrease
the security in order to interoperate with old servers better.
This adds three new options to control the behavior of TCP keepalives:
- CURLOPT_TCP_KEEPALIVE: enable/disable probes
- CURLOPT_TCP_KEEPIDLE: idle time before sending first probe
- CURLOPT_TCP_KEEPINTVL: delay between successive probes
While not all operating systems support the TCP_KEEPIDLE and
TCP_KEEPINTVL knobs, the library will still allow these options to be
set by clients, silently ignoring the values.
Do not try to resolve interfaces names via DNS by recognizing interface
names in a few ways. If the interface option argument has a prefix of
"if!" then treat the argument as only an interface. Similarly, if the
interface argument is the name of an interface (even if it does not have
an IP address assigned), treat it as an interface name. Finally, if the
interface argument is prefixed by "host!" treat it as a hostname that
must be resolved by /etc/hosts or DNS.
These changes allow a client using the multi interfaces to avoid
blocking on name resolution if the interface loses its IP address or
disappears.
If the option is set to 0, the default timeout will be used - which in
modern libcurl versions equals 300 seconds (== 5 minutes).
Bug: http://curl.haxx.se/mail/lib-2011-12/0051.html
Reported by: Vladimir Grishchenko
When the new socket is created for an active connection, it is now done
using the open socket callback.
Test case 596 was modified to run fine, although it hides the fact that
the close callback is still called too many times, as it also gets
called for closing sockets that were created with accept().
Added pop3 username and password example as well as an explanation of
how path part of the URL is used under pop3.
Additionally have corrected a couple of typos.
Slight rewording of the CURLOPT_URL SMTP sub-section.
Corrected the incorrect use of hyphens on the three uses of
"zero-terminated" with "zero terminated" to match the rest of the
document.
Corrected the use of an out of place hyphen in CURLOPT_NOPROXY section.
Allow (*curl_write_callback) write callbacks to return
CURL_WRITEFUNC_OUT_OF_MEMORY to properly indicate libcurl of OOM conditions
inside the callback itself.
