HTTP upload was disconnected:
"What appears to be happening is that my system (Linux 2.6.17 and 2.6.13) is
setting *only* POLLHUP on poll() when the conditions in my previous mail
occur. As you can see, select.c:Curl_select() does not check for POLLHUP. So
basically what was happening, is poll() was returning immediately (with
POLLHUP set), but when Curl_select() looked at the bits, neither POLLERR or
POLLOUT was set. This still caused Curl_readwrite() to be called, which
quickly returned. Then the transfer() loop kept continuing at full speed
forever."
header in a third, not suppported by libcurl, format and we agreed that we
could make the parser more forgiving to accept all the three found
variations.
responded with a single status line and no headers nor body. Starting now, a
HTTP response on a persistent connection (i.e not set to be closed after the
response has been taken care of) must have Content-Length or chunked
encoding set, or libcurl will simply assume that there is no body.
To my horror I learned that we had no less than 57(!) test cases that did bad
HTTP responses like this, and even the test http server (sws) responded badly
when queried by the test system if it is the test system. So although the
actual fix for the problem was tiny, going through all the newly failing test
cases got really painful and boring.
KNOWN_BUGS #25, which happens when a proxy closes the connection when
libcurl has sent CONNECT, as part of an authentication negotiation. Starting
now, libcurl will re-connect accordingly and continue the authentication as
it should.
case when 401 or 407 are returned, *IF* no auth credentials have been given.
The CURLOPT_FAILONERROR option is not possible to make fool-proof for 401
and 407 cases when auth credentials is given, but we've now covered this
somewhat more.
You might get some amounts of headers transferred before this situation is
detected, like for when a "100-continue" is received as a response to a
POST/PUT and a 401 or 407 is received immediately afterwards.
Added test 281 to verify this change.
cross-compiling) in order to detect problems with run-time libraries that
otherwise would occur when the sizeof tests for curl_off_t would run and
thus be much more confusing to users. The check of course should run after
all lib-checks are done and before any other test is used that would run an
executable built for testing-purposes.
to the CURLOPT_DEBUGFUNCTION callback has been fixed (it was erroneously
included as part of the header). A message was also added to the
command line tool to show when data is being sent, enabled when
--verbose is used.
and while doing so it became apparent that the current timeout system for
the socket API really was a bit awkward since it become quite some work to
be sure we have the correct timeout set.
Jeff then provided the new CURLMOPT_TIMERFUNCTION that is yet another
callback the app can set to get to know when the general timeout time
changes and thus for an application like hiperfifo.c it makes everything a
lot easier and nicer. There's a CURLMOPT_TIMERDATA option too of course in
good old libcurl tradition.
would crash if a bad function sequence was used when shutting down after
using the multi interface (i.e using easy_cleanup after multi_cleanup) so
precautions have been added to make sure it doesn't any more - test case 529
was added to verify.
handle that is part of a multi handle first removes the handle from the
stack.
- Added CURLOPT_SSL_SESSIONID_CACHE and --no-sessionid to disable SSL
session-ID re-use on demand since there obviously are broken servers out
there that misbehave with session-IDs used.
while not fixing things very nicely, it does make the SOCKS5 proxy
connection slightly better as it now acknowledges the timeout for connection
and it no longer segfaults in the case when SOCKS requires authentication
and you did not specify username:password.
send the whole request at once, even though the Expect: header was disabled
by the application. An effect of this change is also that small (< 1024
bytes) POSTs are now always sent without Expect: header since we deem it
more costly to bother about that than the risk that we send the data in
vain.
CURLOPT_NOBODY is set true. PREQUOTE is then run roughly at the same place
in the command sequence as it would have run if there would've been a
transfer.
we did wrong and patched it: When nodes were removed from the splay tree,
and we didn't properly remove it from the splay tree when an easy handle was
removed from a multi stack and thus we could wrongly leave a node in the
splay tree pointing to (bad) memory.
the crash was that libcurl internally was a bit confused about who owned the
DNS cache at all times so if you created an easy handle that uses a shared
DNS cache and added that to a multi handle it would crash. Now we keep more
careful internal track of exactly what kind of DNS cache each easy handle
uses: None, Private (allocated for and used only by this single handle),
Shared (points to a cache held by a shared object), Global (points to the
global cache) or Multi (points to the cache within the multi handle that is
automatically shared between all easy handles that are added with private
caches).
CURLOPT_MAX_RECV_SPEED_LARGE that limit tha maximum rate libcurl is allowed
to send or receive data. This kind of adds the the command line tool's
option --limit-rate to the library.
The rate limiting logic in the curl app is now removed and is instead
provided by libcurl itself. Transfer rate limiting will now also work for -d
and -F, which it didn't before.
autotools project, which optionally (default=yes) uses libcurl on a system
without a (usable) libcurl installation, but not specifying
`--without-libcurl', configure determines correctly that no libcurl is
available, however, the LIBCURL variable gets expanded to `LIBCURL = -lcurl'
in the resulting Makefiles.
David Shaw fixed the flaw.
multi stack and that easy handle had already been used to do one or more
easy interface transfers, as then the code threw away the previously used
DNS cache without properly freeing it.
(http://curl.haxx.se/bug/view.cgi?id=1481217), with follow-ups by Michele Bini
and David Byron. libcurl previously wrongly used GetLastError() on windows to
get error details after socket-related function calls, when it really should
use WSAGetLastError() instead.
When changing to this, the former function Curl_ourerrno() is now instead
called Curl_sockerrno() as it is necessary to only use it to get errno from
socket-related functions as otherwise it won't work as intended on Windows.
(http://curl.haxx.se/bug/view.cgi?id=1480821) He found and identified a
problem with how libcurl dealt with GnuTLS and a case where gnutls returned
GNUTLS_E_AGAIN indicating it would block. It would then return an unexpected
return code, making Curl_ssl_send() confuse the upper layer - causing random
28 bytes trash data to get inserted in the transfered stream.
The proper fix was to make the Curl_gtls_send() function return the proper
return codes that the callers would expect. The Curl_ossl_send() function
already did this.
(http://curl.haxx.se/mail/lib-2006-02/0154.html) by adding the NTLM hash
function in addition to the LM one and making some other adjustments in the
order the different parts of the data block are sent in the Type-2 reply.
Inspiration for this work was taken from the Firefox NTLM implementation.
I edited the existing 21(!) NTLM test cases to run fine with these news. Due
to the fact that we now properly include the host name in the Type-2 message
the test cases now only compare parts of that chunk.
--enable-debug, as then curl used free() on memory allocated both with
normal malloc() and with libcurl-provided functions, when the latter MUST be
freed with curl_free() in debug builds.
