This new option tells curl to not work around a security flaw in the
SSL3 and TLS1.0 protocols. It uses the new libcurl option
CURLOPT_SSL_OPTIONS with the CURLSSLOPT_ALLOW_BEAST bit set.
Allow an appliction to set libcurl specific SSL options. The first and
only options supported right now is CURLSSLOPT_ALLOW_BEAST.
It will make libcurl to disable any work-arounds the underlying SSL
library may have to address a known security flaw in the SSL3 and TLS1.0
protocol versions.
This is a reaction to us unconditionally removing that behavior after
this security advisory:
http://curl.haxx.se/docs/adv_20120124B.html
... it did however cause a lot of programs to fail because of old
servers not liking this work-around. Now programs can opt to decrease
the security in order to interoperate with old servers better.
Use the new library CURLOPT_TCP_KEEPALIVE rather than disabling this via
the sockopt callback. If --keepalive-time is used, apply the value to
CURLOPT_TCP_KEEPIDLE and CURLOPT_TCP_KEEPINTVL.
This adds three new options to control the behavior of TCP keepalives:
- CURLOPT_TCP_KEEPALIVE: enable/disable probes
- CURLOPT_TCP_KEEPIDLE: idle time before sending first probe
- CURLOPT_TCP_KEEPINTVL: delay between successive probes
While not all operating systems support the TCP_KEEPIDLE and
TCP_KEEPINTVL knobs, the library will still allow these options to be
set by clients, silently ignoring the values.
As is pointed out in this bug report, there can indeed be situation
where --stderr has a point even when the "real" stderr can be
redirected. Remove the superfluous and wrong comment.
bug: http://curl.haxx.se/bug/view.cgi?id=3476020
These examples show how to fetch a single message (RETR command) and how to
list all the messages in a given mailbox (LIST command), with authentication
via SSL.
They were both based on the https.c example.
The INTERNALS document suggested that compatibility should be
maintained with perl version 4, but this was untrue - scripts such as
chksource.pl and runtests.pl use perl5-isms.
1- Two new error codes are introduced.
CURLE_FTP_ACCEPT_FAILED to be set whenever ACCEPTing fails because of
FTP server connected.
CURLE_FTP_ACCEPT_TIMEOUT to be set whenever ACCEPTing timeouts.
Neither of these errors are considered fatal and control connection
remains OK because it could just be a firewall blocking server to
connect to the client.
2- One new setopt option was introduced.
CURLOPT_ACCEPTTIMEOUT_MS
It sets the maximum amount of time FTP client is going to wait for a
server to connect. Internal default accept timeout is 60 seconds.
Parameters were underquoted, resulting in
warning: AC_LANG_CONFTEST: no AC_LANG_SOURCE call detected in body
Signed-off-by: Bernhard Reutner-Fischer <rep.dot.nop@gmail.com>
Document the possibility of providing multiple values using the ":"
separator, and the fact that the default value will be ignored if the
option is used.
Do not try to resolve interfaces names via DNS by recognizing interface
names in a few ways. If the interface option argument has a prefix of
"if!" then treat the argument as only an interface. Similarly, if the
interface argument is the name of an interface (even if it does not have
an IP address assigned), treat it as an interface name. Finally, if the
interface argument is prefixed by "host!" treat it as a hostname that
must be resolved by /etc/hosts or DNS.
These changes allow a client using the multi interfaces to avoid
blocking on name resolution if the interface loses its IP address or
disappears.
If the option is set to 0, the default timeout will be used - which in
modern libcurl versions equals 300 seconds (== 5 minutes).
Bug: http://curl.haxx.se/mail/lib-2011-12/0051.html
Reported by: Vladimir Grishchenko
Adds a timer based off of CURLINFO_TOTAL_TIME that is used to perform
certain actions after a minimum amount of time has passed using the
progress function. As a consequence the curl handle is now also passed
into the progress function. Progress example now also includes an
example of how to retreive the TOTAL_TIME and print it out.
When the new socket is created for an active connection, it is now done
using the open socket callback.
Test case 596 was modified to run fine, although it hides the fact that
the close callback is still called too many times, as it also gets
called for closing sockets that were created with accept().
Experience has shown that the symbols-in-versions file is very useful to
applications that want to build with a wide range of libcurl versions.
It is however easy to get it wrong and the source gets a bit messy with
all the fixed numerical comparisions.
The point of this script is to provide an easy-to-use macro for libcurl-
using applications to do preprocessor checks for specific libcurl
defines, and yet make the code clearly show what the macro is used for.
Added pop3 username and password example as well as an explanation of
how path part of the URL is used under pop3.
Additionally have corrected a couple of typos.
Don't even declare the struct members for disabled features
Introducing the CURLSHE_NOT_BUILT_IN return code for the share interface
when trying to set a sharing option that has been disabled (or not
enabled) in the library.
Slight rewording of the CURLOPT_URL SMTP sub-section.
Corrected the incorrect use of hyphens on the three uses of
"zero-terminated" with "zero terminated" to match the rest of the
document.
Corrected the use of an out of place hyphen in CURLOPT_NOPROXY section.
Allow (*curl_write_callback) write callbacks to return
CURL_WRITEFUNC_OUT_OF_MEMORY to properly indicate libcurl of OOM conditions
inside the callback itself.
If a socket is larger than FD_SETSIZE, avoid using FD_SET() on the
platforms where this is possible.
Bug: http://curl.haxx.se/bug/view.cgi?id=3413274
Reported by: Tim Starling
Zero-copy and "Avoid having to remove/readd handles" are not really
features we think are worthwhile to add. Removed.
SRP features have been added already, removed.
11.9 IPv6 addresses with globbing added
