New test 666 checks this is effective.
As upload buffer size is significant in this kind of tests, shorten it
in similar test 652.
Fixes#4860Closes#4833
Reported-by: RuurdBeerstra on github
Input buffer filling may delay the data sending if data reads are slow.
To overcome this problem, file and callback data reads do not accumulate
in buffer anymore. All other data (memory data and mime framing) are
considered as fast and still concatenated in buffer.
As this may highly impact performance in terms of data overhead, an early
end of part data check is added to spare a read call.
When encoding a part's data, an encoder may require more bytes than made
available by a single read. In this case, the above rule does not apply
and reads are performed until the encoder is able to deliver some data.
Tests 643, 644, 645, 650 and 654 have been adapted to the output data
changes, with test data size reduced to avoid the boredom of long lists of
1-byte chunks in verification data.
New test 667 checks mimepost using single-byte read callback with encoder.
New test 668 checks the end of part data early detection.
Fixes#4826
Reported-by: MrdUkk on github
In case a read callback returns a status (pause, abort, eof,
error) instead of a byte count, drain the bytes read so far but
remember this status for further processing.
Takes care of not losing data when pausing, and properly resume a
paused mime structure when requested.
New tests 670-673 check unpausing cases, with easy or multi
interface and mime or form api.
Fixes#4813
Reported-by: MrdUkk on github
New test 666 checks this is effective.
As upload buffer size is significant in this kind of tests, shorten it
in similar test 652.
Fixes#4860
Reported-by: RuurdBeerstra on github
Input buffer filling may delay the data sending if data reads are slow.
To overcome this problem, file and callback data reads do not accumulate
in buffer anymore. All other data (memory data and mime framing) are
considered as fast and still concatenated in buffer.
As this may highly impact performance in terms of data overhead, an early
end of part data check is added to spare a read call.
When encoding a part's data, an encoder may require more bytes than made
available by a single read. In this case, the above rule does not apply
and reads are performed until the encoder is able to deliver some data.
Tests 643, 644, 645, 650 and 654 have been adapted to the output data
changes, with test data size reduced to avoid the boredom of long lists of
1-byte chunks in verification data.
New test 664 checks mimepost using single-byte read callback with encoder.
New test 665 checks the end of part data early detection.
Fixes#4826
Reported-by: MrdUkk on github
In case a read callback returns a status (pause, abort, eof,
error) instead of a byte count, drain the bytes read so far but
remember this status for further processing.
Takes care of not losing data when pausing, and properly resume a
paused mime structure when requested.
New tests 670-673 check unpausing cases, with easy or multi
interface and mime or form api.
Fixes#4813
Reported-by: MrdUkk on github
Closes#4833
This reduces the HTTP/2 window size to 32 MB since libcurl might have to
buffer up to this amount of data in memory and yet we don't want it set
lower to potentially impact tranfer performance on high speed networks.
Requires nghttp2 commit b3f85e2daa629
(https://github.com/nghttp2/nghttp2/pull/1444) to work properly, to end
up in the next release after 1.40.0.
Fixes#4939Closes#4940
It is still possible to override the executable to run during the test,
using the <tool> tag, but this patch removes the requirement that the
tag must be present for unit tests.
It also removes the possibility of human error when existing test cases
are used as the basis for new tests, as recently witnessed in 81c37124.
Reviewed-by: Daniel Stenberg
Closes#4976
When doing a request with a body + Expect: 100-continue and the server
responds with a 417, the same request will be retried immediately
without the Expect: header.
Added test 357 to verify.
Also added a control instruction to tell the sws test server to not read
the request body if Expect: is present, which the new test 357 uses.
Reported-by: bramus on github
Fixes#4949Closes#4964
Note: The RCPT TO command isn't required to advertise to the server that
it contains UTF-8 characters, instead the server is told that a mail may
contain UTF-8 in any envelope command via the MAIL command.
Support the SMTPUTF8 extension when sending mailbox information in the
MAIL command (FROM and AUTH parameters). Non-ASCII domain names will
be ACE encoded, if IDN is supported, whilst non-ASCII characters in
the local address part are passed to the server.
Reported-by: ygthien on github
Fixes#4828
The alt-svc cache survives a call to curl_easy_reset fine, but the file
name to use for saving the cache was cleared. Now the alt-svc cache has
a copy of the file name to survive handle resets.
Added test 1908 to verify.
Reported-by: Craig Andrews
Fixes#4898Closes#4902
RFC 7616 section 3.4 (The Authorization Header Field) states that "For
historical reasons, a sender MUST NOT generate the quoted string syntax
for the following parameters: algorithm, qop, and nc". This removes the
quoting for the algorithm parameter.
Reviewed-by: Steve Holme
Closes#4890
... as this is already done much earlier in the URL parser.
Also add test case 894 that verifies that pop3 with an encodedd CR in
the user name is rejected.
Closes#4887
Previously it was stored in a global state which contributed to
curl_global_init's thread unsafety. This boolean is now instead figured
out in curl_multi_init() and stored in the multi handle. Less effective,
but thread safe.
Closes#4851
- Add new error code CURLE_QUIC_CONNECT_ERROR for QUIC connection
errors.
Prior to this change CURLE_FAILED_INIT was used, but that was not
correct.
Closes https://github.com/curl/curl/pull/4754
It was removed for output containing ' =' via `s/ =.*//`. With classic
MinGW, this made lines with `free()` end with CRLF, but lines with e.g.
`malloc()` end with only LF. The tests expect LF only.
Closes https://github.com/curl/curl/pull/4788
Previously it would end up with an uninitialized memory buffer that
would lead to a crash or junk getting output.
Added test 1271 to verify.
Reported-by: Brian Carpenter
Closes#4786
Prior to this change tests that required NTLM feature did not require
SSL feature.
There are pending changes to cmake builds that will allow enabling NTLM
in non-SSL builds in Windows. In that case the NTLM auth strings created
are different from what is expected by the NTLM tests and they fail:
"The issue with NTLM is that previous non-SSL builds would not enable
NTLM and so the NTLM tests would be skipped."
Assisted-by: marc-groundctl@users.noreply.github.com
Ref: https://github.com/curl/curl/pull/4717#issuecomment-566218729
Closes https://github.com/curl/curl/pull/4768
Even if the initial request line wasn't found. With the fix to 1455, the
test number is now detected correctly.
(Problem found when running tests in random order.)
Closes#4744
