Added test 348 to verify. Added a 'STOR' command to the test FTP
server to enable test 348. Documented the command in FILEFORMAT.md
Reported-by: Duncan Wilcox
Fixes#6016Closes#6017
This allows us to make test cases to use base64 at run-time and still
use and verify information determined at run-time, such as the IMAP test
server's port number in test 842.
This change makes 12 tests run again that basically never ran since we
moved to dynamic port numbers.
ftpserver.pl is adjusted to load test instructions and test number from
the preprocessed test file.
FILEFORMAT.md now documents the new base64 encoding syntax.
Reported-by: Marcel Raad
Fixes#5761Closes#5775
Rely on tests asking the names to get refused instead - test servers
should be as dumb as possible. Edited test 914, 955 and 959 accordingly.
Closes#5639
FTP, IMAP, POP3, SMTP and their IPv6 versions are now all on dynamic
ports
Test 842-845 are unfortunately a bit hard to move over to this concept
right now and require "default port" still...
Note: The RCPT TO command isn't required to advertise to the server that
it contains UTF-8 characters, instead the server is told that a mail may
contain UTF-8 in any envelope command via the MAIL command.
Support the SMTPUTF8 extension when sending mailbox information in the
MAIL command (FROM and AUTH parameters). Non-ASCII domain names will
be ACE encoded, if IDN is supported, whilst non-ASCII characters in
the local address part are passed to the server.
Reported-by: ygthien on github
Fixes#4828
The dot character between the host and the tld was not being escaped,
which meant it specified a match of 'any' character rather than an
explicit dot separator.
Additionally removed the dot character from the host name as it allowed
the following to be specified as a valid address in our test cases:
<bad@example......com>
Both are typos from 98f7ca7 and 8880f84 :(
I can't remember whether my intention was to allow sub-domains to be
specified in the host or not with these additional dots, but by placing
it outside of the host means it can only be specified once per domain
and by placing a + after the new grouping support for sub-domains is
kept.
Closes#4912
This enables the use of Windows Subsystem for Linux (WSL) to run the
testsuite against Windows binaries while using Linux servers.
This commit introduces the following environment variables:
- CURL_TEST_EXE_EXT: set the executable extension for all components
- CURL_TEST_EXE_EXT_TOOL: set it for the curl tool only
- CURL_TEST_EXE_EXT_SSH: set it for the SSH tools only
Later testcurl.pl could be adjusted to make use of those variables.
- CURL_TEST_EXE_EXT_SRV: set it for the test servers only
(This is one of several commits to support use of WSL for the tests.)
Closes https://github.com/curl/curl/pull/3899
... and add "MAILINDEX".
As described in #2789, this is a suggested solution. Changing UID=xx to
actually get mail with UID xx and add "MAILINDEX" to get a mail with a
special index in the mail box (old behavior). So MAILINDEX=1 gives the
first non deleted mail in the mail box.
Fixes#2789Closes#2815
RFC 5321 4.1.1.4 specifies the CRLF terminating the DATA command
should be taken into account when chasing the <CRLF>.<CRLF> end marker.
Thus a leading dot character in data is also subject to escaping.
Tests 911 and test server are adapted to this situation.
New tests 951 and 952 check proper handling of initial dot in data.
Closes#2304
For pop3/imap/smtp, added test 891 to somewhat verify the pop3
case.
For this, I enhanced the pingpong test server to be able to send back
responses with LF-only instead of always using CRLF.
Closes#2150
... as the test cases themselves do that and it makes it easier to add
crazy test cases.
Test 800 updated to use user name + password that need quoting.
Test 856 updated to trigger an auth fail differently.
Ref: #1902
We're mostly saying just "curl" in lower case these days so here's a big
cleanup to adapt to this reality. A few instances are left as the
project could still formally be considered called cURL.
According to section 2.2 of RFC959 the End-of-Line is defined as:
The end-of-line sequence defines the separation of printing
lines. The sequence is Carriage Return, followed by Line Feed.
Verified by sniffing traffic between a Windows FTP client (FileZilla)
and Unix-hosted FTP server (ProFTPD).
Also, make the ftp server return a canned response that doesn't
cause XML verification problems. Although the test file format
isn't technically XML, it's still handy to be able to use XML
tools to verify and manipulate them.
Previously LIST always returned a fixed hardcoded list that the ftp
server code knew about, mostly since the server didn't get any test case
number in the LIST scenario. Starting now, doing a CWD to a directory
named test-[number] will make the test server remember that number and
consider it a test case so that a subsequent LIST command will send the
<data> section of that test case back.
It allows LIST tests to be made more similar to how all other tests
work.
Test 100 was updated to provide its own directory listing.
Following the addition of informational commands to the SMTP protocol,
the test server is no longer required to return the verified server
information in responses that curl only outputs in verbose mode.
Instead, a similar detection mechanism to that used by FTP, IMAP and
POP3 can now be used.
This commit replaces that of 9f260b5d66 because according to RFC-2449,
section 6, there is no APOP capability "...even though APOP is an
optional command in [POP3]. Clients discover server support of APOP by
the presence in the greeting banner of an initial challenge enclosed in
angle brackets."
SASL downgrade tests: 833, 835, 879, 881, 935 and 937 would fail as
they contained a minus sign in their authentication mechanism and this
would be missed by the custom reply parser.
Daniel Stenberg