When libcurl retries a connection due to it being "seemingly dead" or by
REFUSED_STREAM, it will now only do it up five times before giving up,
to avoid never-ending loops.
Reported-by: Dima Tisnek
Bug: https://curl.haxx.se/mail/lib-2020-03/0044.htmlCloses#5074
Make sure each separate index in connn->tempaddr[] is used for a fixed
family (and only that family) during the connection process.
If family one takes a long time and family two fails immediately, the
previous logic could misbehave and retry the same family two address
repeatedly.
Reported-by: Paul Vixie
Reported-by: Jay Satiro
Fixes#5083Fixes#4954Closes#5089
- Ignore CURLE_NOT_BUILT_IN errors returned by c-ares functions in
curl_easy_duphandle.
Prior to this change if c-ares was used as the resolver backend and
either it was too old or libcurl was built without IPv6 support then
some of our resolver functions could return CURLE_NOT_BUILT_IN to
curl_easy_duphandle causing it to fail.
Caused by c8f086b which shipped in 7.69.1.
Reported-by: Karl Chen
Fixes https://github.com/curl/curl/issues/5097
Closes https://github.com/curl/curl/pull/5100
1. The socks4 state machine was broken in the host resolving phase
2. The code now insists on IPv4-only when using SOCKS4 as the protocol
only supports that.
Regression from #4907 and 4a4b63d, shipped in 7.69.0
Reported-by: amishmm on github
Bug: https://github.com/curl/curl/issues/5053#issuecomment-596191594Closes#5061
New test 666 checks this is effective.
As upload buffer size is significant in this kind of tests, shorten it
in similar test 652.
Fixes#4860Closes#4833
Reported-by: RuurdBeerstra on github
Input buffer filling may delay the data sending if data reads are slow.
To overcome this problem, file and callback data reads do not accumulate
in buffer anymore. All other data (memory data and mime framing) are
considered as fast and still concatenated in buffer.
As this may highly impact performance in terms of data overhead, an early
end of part data check is added to spare a read call.
When encoding a part's data, an encoder may require more bytes than made
available by a single read. In this case, the above rule does not apply
and reads are performed until the encoder is able to deliver some data.
Tests 643, 644, 645, 650 and 654 have been adapted to the output data
changes, with test data size reduced to avoid the boredom of long lists of
1-byte chunks in verification data.
New test 667 checks mimepost using single-byte read callback with encoder.
New test 668 checks the end of part data early detection.
Fixes#4826
Reported-by: MrdUkk on github
In case a read callback returns a status (pause, abort, eof,
error) instead of a byte count, drain the bytes read so far but
remember this status for further processing.
Takes care of not losing data when pausing, and properly resume a
paused mime structure when requested.
New tests 670-673 check unpausing cases, with easy or multi
interface and mime or form api.
Fixes#4813
Reported-by: MrdUkk on github
With c-ares the dns parameters lives in ares_channel. Store them in the
curl handle and set them again in easy_duphandle.
Regression introduced in #3228 (6765e6d), shipped in curl 7.63.0.
Fixes#4893Closes#5020
Signed-off-by: Ernst Sjöstrand <ernst.sjostrand@verisure.com>
- Don't check errno on wakeup socket if sread returned 0 since sread
doesn't set errno in that case.
This is a follow-up to cf7760a from several days ago which fixed
Curl_multi_wait to stop busy looping sread on the non-blocking wakeup
socket if it was closed (ie sread returns 0). Due to a logic error it
was still possible to busy loop in that case if errno == EINTR.
Closes https://github.com/curl/curl/pull/5047
As we have logic that checks if we get a >= 400 reponse code back before
the upload is done, which then got confused since it wasn't "done" but
yet there was no data to send!
Reported-by: IvanoG on github
Fixes#4996Closes#5002
New test 666 checks this is effective.
As upload buffer size is significant in this kind of tests, shorten it
in similar test 652.
Fixes#4860
Reported-by: RuurdBeerstra on github
Input buffer filling may delay the data sending if data reads are slow.
To overcome this problem, file and callback data reads do not accumulate
in buffer anymore. All other data (memory data and mime framing) are
considered as fast and still concatenated in buffer.
As this may highly impact performance in terms of data overhead, an early
end of part data check is added to spare a read call.
When encoding a part's data, an encoder may require more bytes than made
available by a single read. In this case, the above rule does not apply
and reads are performed until the encoder is able to deliver some data.
Tests 643, 644, 645, 650 and 654 have been adapted to the output data
changes, with test data size reduced to avoid the boredom of long lists of
1-byte chunks in verification data.
New test 664 checks mimepost using single-byte read callback with encoder.
New test 665 checks the end of part data early detection.
Fixes#4826
Reported-by: MrdUkk on github
