assumed this used the DICT protocol. While guessing protocols will remain
fuzzy, I've now made sure that the host names must start with "[protocol]."
for them to be a valid guessable name. I also removed "https" as a prefix that
indicates HTTPS, since we hardly ever see any host names using that.
using a custom Host: header and curl fails to send a request on a re-used
persistent connection and thus creates a new connection and resends it. It
then sent two Host: headers. Cyrill's analysis was posted here:
http://curl.haxx.se/mail/archive-2005-01/0022.html
problem with the version byte and the check for bad versions. Bruce has lots
of clues on this, and based on his suggestion I've now removed the check of
that byte since it seems to be able to contain 1 or 5.
#1098843. In short, a shared DNS cache was setup for a multi handle and when
the shared cache was deleted before the individual easy handles, the latter
cleanups caused read/writes to already freed memory.
reported on Solaris) problem where the size_t check fails due to the SSL libs
being found in a dir not searched through by the run-time linker.
patch-tracker entry #1081707.
libcurl always and unconditionally overwrote a stack-based array with 3 zero
bytes. I edited the fix to make it less likely to occur again (and added
a comment explaining the reason to the buffer size).
libcurl without cookie support. This is mainly useful if you want to build a
minimalistic libcurl with no cookies support at all. Like for embedded
systems or similar.
response. Previously, libcurl would re-resolve the host name with the new
port number and attempt to connect to that, while it should use the IP from
the control channel. This bug made it hard to EPSV from an FTP server with
multiple IP addresses!
(http://qa.mandrakesoft.com/show_bug.cgi?id=12285), when connecting to an
IPv6 host with FTP, --disable-epsv (or --disable-eprt) effectively disables
the ability to transfer a file. Now, when connected to an FTP server with
IPv6, these FTP commands can't be disabled even if asked to with the
available libcurl options.
If EPSV, EPRT or LPRT is tried and doesn't work, it will not be retried on
the same server again even if a following request is made using a persistent
connection.
If a second request is made to a server, requesting a file from the same
directory as the previous request operated on, libcurl will no longer make
that long series of CWD commands just to end up on the same spot. Note that
this is only for *exactly* the same dir. There is still room for improvements
to optimize the CWD-sending when the dirs are only slightly different.
Added test 210, 211 and 212 to verify these changes. Had to improve the
test script too and added a new primitive to the test file format.
file that was already completely downloaded caused an error, while it
doesn't if you don't use --fail! I added test case 194 to verify the fix.
Grrr. CURLOPT_FAILONERROR is now added to the list stuff to remove in
libcurl v8 due to all the kludges needed to support it.
CURLOPT_FOLLOWLOCATION, libcurl reported error if a redirect happened even if
the new URL would provide the resumed file. Test case 188 added to verify the
fix (together with existing test 99).
based) IDN conversion fails. This is really due to a missing suitable
function in the libidn API that I hope we can remove once libidn gets a
function like this.
https://bugzilla.redhat.com/bugzilla/show_bug.cgi?id=134133) and not to anyone
involved in the curl project! This happens when you try to curl a file from a
proftpd site using SSL. It seems proftpd sends a somewhat unorthodox PASS
response code (232 instead of 230). I relaxed the response code check to deal
with this and similar cases.
formposts no longer include the path part. If you _really_ want them, you
must provide your preferred full file name with CURLFORM_FILENAME.
Added detection for libgen.h and basename() to configure. My custom
basename() replacement function for systems without it, might be a bit too
naive...
Updated 6 test cases to make them work with the stripped paths.
app to retrieve the errno variable after a (connect) failure. It will make
sense to provide this for more failures in a more generic way, but let's
start like this.
replacement, curl only replaced the Host: header on the initial request
and didn't replace it on the following ones. This resulted in requests with
two Host: headers.
Now, curl checks if the location is on the same host as the initial request
and then continues to replace the Host: header. And when it moves to another
host, it doesn't replace the Host: header but it also doesn't make the
second Host: header get used in the request.
This change is verified by the two new test cases 184 and 185.
