// usb host experiments....


//void * periodictable[64]  __attribute__ ((section(".dmabuffers"), used, aligned(4096)))
uint32_t periodictable[64] __attribute__ ((aligned(4096)));


void setup()
{
	pinMode(32, OUTPUT);	// pin 32 = USB switch, high=connect device
	digitalWrite(32, LOW);
	while (!Serial) ; // wait
	print("USB Host Testing");
	MPU_RGDAAC0 |= 0x30000000;
	MCG_C1 |= MCG_C1_IRCLKEN;  // enable MCGIRCLK 32kHz
	OSC0_CR |= OSC_ERCLKEN;
	SIM_SOPT2 |= SIM_SOPT2_USBREGEN; // turn on USB regulator
	SIM_SOPT2 &= ~SIM_SOPT2_USBSLSRC; // use IRC for slow clock
	print("power up USBHS PHY");
	SIM_USBPHYCTL |= SIM_USBPHYCTL_USBDISILIM; // disable USB current limit
	//SIM_USBPHYCTL = SIM_USBPHYCTL_USBDISILIM | SIM_USBPHYCTL_USB3VOUTTRG(6); // pg 237
	SIM_SCGC3 |= SIM_SCGC3_USBHSDCD | SIM_SCGC3_USBHSPHY | SIM_SCGC3_USBHS;
	USBHSDCD_CLOCK = 33 << 2;
	print("init USBHS PHY & PLL");
	// init process: page 1681-1682
	USBPHY_CTRL &= ~USBPHY_CTRL_SFTRST;	// CTRL pg 1698
	USBPHY_CTRL &= ~USBPHY_CTRL_CLKGATE;
	USBPHY_PLL_SIC |= USBPHY_PLL_SIC_PLL_POWER;
	USBPHY_PLL_SIC |= USBPHY_PLL_SIC_PLL_DIV_SEL(1);  // PLL_SIC pg 1708
	// wait for the PLL to lock
	int count=0;
	while ((USBPHY_PLL_SIC & USBPHY_PLL_SIC_PLL_LOCK) == 0) {
		count++;
	}
	print("PLL locked, waited ", count);
	USBPHY_PLL_SIC |= USBPHY_PLL_SIC_PLL_EN_USB_CLKS;
	USBPHY_PWD = 0;
	delay(10);

	// sanity check, connect 470K pullup & 100K pulldown and watch D+ voltage change
	//USBPHY_ANACTRL_CLR = (1<<10); // turn off both 15K pulldowns... works! :)

	// sanity check, output clocks on pin 9 for testing
	//SIM_SOPT2 = SIM_SOPT2 & (~SIM_SOPT2_CLKOUTSEL(7)) | SIM_SOPT2_CLKOUTSEL(3); // LPO 1kHz
	//SIM_SOPT2 = SIM_SOPT2 & (~SIM_SOPT2_CLKOUTSEL(7)) | SIM_SOPT2_CLKOUTSEL(2); // Flash
	//SIM_SOPT2 = SIM_SOPT2 & (~SIM_SOPT2_CLKOUTSEL(7)) | SIM_SOPT2_CLKOUTSEL(6); // XTAL
	//SIM_SOPT2 = SIM_SOPT2 & (~SIM_SOPT2_CLKOUTSEL(7)) | SIM_SOPT2_CLKOUTSEL(7); // IRC 48MHz
	//SIM_SOPT2 = SIM_SOPT2 & (~SIM_SOPT2_CLKOUTSEL(7)) | SIM_SOPT2_CLKOUTSEL(4); // MCGIRCLK
	//CORE_PIN9_CONFIG = PORT_PCR_MUX(5);  // CLKOUT on PTC3 Alt5 (Arduino pin 9)

// EHCI registers         page  default
// --------------         ----  -------
// USBHS_USBCMD           1599  00080000
// USBHS_USBSTS           1602  00000000
// USBHS_USBINTR          1606  00000000
// USBHS_FRINDEX          1609  00000000
// USBHS_PERIODICLISTBASE 1610  undefine
// USBHS_ASYNCLISTADDR    1612  undefine
// USBHS_PORTSC           1619  00002000
// USBHS_USBMODE          1629  00005000

	print("begin ehci reset");
	USBHS_USBCMD |= USBHS_USBCMD_RST;
	count = 0;
	while (USBHS_USBCMD & USBHS_USBCMD_RST) {
		count;
	}
	print(" reset waited ", count);

	for (int i=0; i < 64; i++) {
		//periodictable[i] = (void *)1;
		periodictable[i] = 1;
	}
	USBHS_USBINTR = 0;
	USBHS_PERIODICLISTBASE = (uint32_t)periodictable;
	USBHS_FRINDEX = 0;
	USBHS_ASYNCLISTADDR = 0;    // TODO: data..

	// turn on the USBHS controller
	USBHS_USBMODE = USBHS_USBMODE_TXHSD(5) | USBHS_USBMODE_CM(3); // host mode
	USBHS_USBCMD = USBHS_USBCMD_ITC(0) | USBHS_USBCMD_RS | USBHS_USBCMD_ASP(3) |
		USBHS_USBCMD_FS2 | USBHS_USBCMD_FS(0) | // periodic table is 64 pointers
		USBHS_USBCMD_PSE;

	USBHS_PORTSC1 |= USBHS_PORTSC_PP;
	//USBHS_PORTSC1 |= USBHS_PORTSC_PFSC; // force 12 Mbit/sec
	//USBHS_PORTSC1 |= USBHS_PORTSC_PHCD; // phy off
}

void port_status()
{
	uint32_t n;

	Serial.print("Port: ");
	n = USBHS_PORTSC1;
	if (n & USBHS_PORTSC_PR) {
		Serial.print("reset ");
	}
	if (n & USBHS_PORTSC_PP) {
		Serial.print("on ");
	} else {
		Serial.print("off ");
	}
	if (n & USBHS_PORTSC_PHCD) {
		Serial.print("phyoff ");
	}
	if (n & USBHS_PORTSC_PE) {
		if (n & USBHS_PORTSC_SUSP) {
			Serial.print("suspend ");
		} else {
			Serial.print("enable ");
		}
	} else {
		Serial.print("disable ");
	}
	Serial.print("speed=");
	switch ((n >> 26) & 3) {
	  case 0: Serial.print("12 Mbps "); break;
	  case 1: Serial.print("1.5 Mbps "); break;
	  case 2: Serial.print("480 Mbps "); break;
	  default: Serial.print("(undef) ");
	}
	if (n & USBHS_PORTSC_HSP) {
		Serial.print("highspeed ");
	}
	if (n & USBHS_PORTSC_OCA) {
		Serial.print("overcurrent ");
	}
	if (n & USBHS_PORTSC_CCS) {
		Serial.print("connected ");
	} else {
		Serial.print("not-connected ");
	}
	// print info about the EHCI status
	Serial.print(" run=");
	Serial.print(USBHS_USBCMD & 1);         // running mode
	Serial.print(",halt=");
	Serial.print((USBHS_USBSTS >> 12) & 1); // halted mode
	Serial.print(",err=");
	Serial.print((USBHS_USBSTS >> 4) & 1);  // error encountered!
	Serial.print(",asyn=");
	Serial.print((USBHS_USBSTS >> 15) & 1); // running the async schedule
	Serial.print(",per=");
	Serial.print((USBHS_USBSTS >> 14) & 1); // running the periodic schedule
	Serial.print(",index=");
	Serial.print(USBHS_FRINDEX);            // periodic index

	Serial.println();
}


void loop()
{
	static unsigned int count=0;

	port_status();
	delay(1);
	count++;
	if (count == 2) {
		Serial.println("Plug in device...");
		digitalWrite(32, HIGH); // connect device
	}
	if (count == 5) {
		Serial.println("Initiate Reset Sequence...");
		USBHS_PORTSC1 |= USBHS_PORTSC_PR;
	}
	if (count == 15) {
		Serial.println("End Reset Sequence...");
		USBHS_PORTSC1 &= ~USBHS_PORTSC_PR;
	}
	if (count > 5000) {
		while (1) ; // stop here
	}
}

void print(const char *s)
{
	Serial.println(s);
	delay(10);
}

void print(const char *s, int num)
{
	Serial.print(s);
	Serial.println(num);
	delay(10);
}