Needed HID Parser to support Bidirectional Transfers
The HidParser code was setup such that the claim for a report, the caller could say I want to claim the whole thinig and allowed callback functions for processing of in buffer and out buffer.
Allow RawHID to contribute Transfer_t
Since RawHID may need more resources than most, maybe it should contribute the additional structures
The constructor for a RAWHID object allows you to specify the top usage
that it wishes to connect to. I used this for example to be able to
connect to a Teensy with the RAWHID associated with emulating the
Serial object.
If a HID Input class says that it wants to claim the whole interface, I
reuse the buffer associated with holding the HID descriptor and use it
for output buffers.
As per the forum posts, worked on combining the claim code for extracting which endpoints are RX and TX and create the pipes and the like.
Also worked on live cases. Reading and writing to AX servos... Found some issues Probably more to find.
I left in some debug code to help find cases of deleting a pipe may hang. Also macros in serial.cpp to set or toggle IO pins (when in debug mode). This helps find where things are happing using Logic Analyzer as a way to find the approriate USB packets.
I did a quick test using the Serial test app, where I can type in lines like:
#38400,7E1
And it reopens the serial port at the specified baud and format. Note the formats the test app looks for is 7E1, 7O1, 8N1, 8N2.
Tested on an FTDI, PL2303 and CH341. I also tested going to Teensy 3.2 CDCACM. But as far as I know the teensy could not care less about Baud/Format.
Unless of course there is a way to query the value and use it to set a Hardware Serial port to it.
This commit adds support for at least some of the Serial boards with the
CH341 chipset, tested using a board from sparkfun as well as one from
Amazon.com
The code was rearranged some of the Claim code and added a VID:DID to Serial Type table that I use to map, such that I know some of these devices have multiple valid setups.
Support Begin/End/Begin - Change baud
Added code to support switching baud rates, or more particular be able to call end() and then call begin(...) with same or different baud rate.
Hopefully some support for also releasing DTR when the end is called.
WIP - Start support for the begin(baud, format)
Adding some support to the code to handle some of the different possible format capabilities.
In particualar trying to handle the parity, number of bits and number of stop bits.
hacked up test app, such that if you type in command line like:
"#9600, 7e1"
It will extract the 9600 as the new baud and try to use format 7e1. I only hard coded a few of these in the test app (8n1, 7e1, 7e2, 8n2)...
Again work in progress. Took me awhile tofigure out how to do this for ch341 boards as I did not see any documents or code that handled this. So had to deduce it from differences in USB packets.
This commit should start to allow some Prolific PL2303 devices to work.
Tis device has a rather more complex initialization process than some
of the other devices.
I have tested this some with one device that I used to use to program
some older RS232 based boards plus talk to an SSC-32 device.
Test case is I am able to talk to SSC-32 and if I type in ver<cr>
It does properly return the version number.
The data I am seeing is pretty close to what
was documented in: https://gist.github.com/tommie/89011c5ac06553d5cdb8
as well as what the Linux driver outputs.
I also incorperated Frank's configuration options.
Have some support in place for the CDCACM serial class code.
It appears to be working for talking to a
Teensy that is programmed USB=Serial
or USB=Serial+...
Also test with an USB2AX board which is a Servo controller for Dynamixel servos (AX-12), that is an Atmega32u2 board programmed using LUFA as the USB library.
