mirror of
https://github.com/gdsports/USBHost_t36
synced 2024-11-21 08:35:03 -05:00
Reset & enable port, but EHCI stops with error :-(
This commit is contained in:
parent
9264f60908
commit
453d04d42d
@ -1,19 +1,26 @@
|
||||
// usb host experiments....
|
||||
|
||||
|
||||
//void * periodictable[64] __attribute__ ((section(".dmabuffers"), used, aligned(4096)))
|
||||
uint32_t periodictable[64] __attribute__ ((aligned(4096)));
|
||||
|
||||
|
||||
void setup()
|
||||
{
|
||||
pinMode(32, OUTPUT); // pin 32 = USB switch, high=connect device
|
||||
digitalWrite(32, LOW);
|
||||
while (!Serial) ; // wait
|
||||
print("USB Host Testing");
|
||||
MPU_RGDAAC0 |= 0x30000000;
|
||||
MCG_C1 |= MCG_C1_IRCLKEN; // enable MCGIRCLK 32kHz
|
||||
OSC0_CR |= OSC_ERCLKEN;
|
||||
SIM_SOPT2 |= SIM_SOPT2_USBREGEN; // turn on USB regulator
|
||||
SIM_SOPT2 &= ~SIM_SOPT2_USBSLSRC; // use IRC for slow clock
|
||||
print("power up USBHS PHY");
|
||||
SIM_USBPHYCTL |= SIM_USBPHYCTL_USBDISILIM; // disable USB current limit
|
||||
SIM_USBPHYCTL = SIM_USBPHYCTL_USBDISILIM | SIM_USBPHYCTL_USB3VOUTTRG(6); // pg 237
|
||||
//SIM_USBPHYCTL = SIM_USBPHYCTL_USBDISILIM | SIM_USBPHYCTL_USB3VOUTTRG(6); // pg 237
|
||||
SIM_SCGC3 |= SIM_SCGC3_USBHSDCD | SIM_SCGC3_USBHSPHY | SIM_SCGC3_USBHS;
|
||||
USBHSDCD_CLOCK = 33 << 2;
|
||||
print("init USBHS PHY & PLL");
|
||||
// init process: page 1681-1682
|
||||
USBPHY_CTRL &= ~USBPHY_CTRL_SFTRST; // CTRL pg 1698
|
||||
@ -52,15 +59,32 @@ void setup()
|
||||
// USBHS_PORTSC 1619 00002000
|
||||
// USBHS_USBMODE 1629 00005000
|
||||
|
||||
print("begin ehci reset");
|
||||
USBHS_USBCMD |= USBHS_USBCMD_RST;
|
||||
count = 0;
|
||||
while (USBHS_USBCMD & USBHS_USBCMD_RST) {
|
||||
count;
|
||||
}
|
||||
print(" reset waited ", count);
|
||||
|
||||
for (int i=0; i < 64; i++) {
|
||||
//periodictable[i] = (void *)1;
|
||||
periodictable[i] = 1;
|
||||
}
|
||||
USBHS_USBINTR = 0;
|
||||
USBHS_PERIODICLISTBASE = 0; // TODO: data..
|
||||
USBHS_PERIODICLISTBASE = (uint32_t)periodictable;
|
||||
USBHS_FRINDEX = 0;
|
||||
USBHS_ASYNCLISTADDR = 0; // TODO: data..
|
||||
|
||||
// turn on the USBHS controller
|
||||
USBHS_USBMODE = USBHS_USBMODE_TXHSD(5) | USBHS_USBMODE_CM(3); // host mode
|
||||
USBHS_USBCMD = USBHS_USBCMD_ITC(8) | USBHS_USBCMD_RS |
|
||||
USBHS_USBCMD_FS2 | USBHS_USBCMD_FS(0); // periodic table is 64 pointers
|
||||
USBHS_USBCMD = USBHS_USBCMD_ITC(0) | USBHS_USBCMD_RS | USBHS_USBCMD_ASP(3) |
|
||||
USBHS_USBCMD_FS2 | USBHS_USBCMD_FS(0) | // periodic table is 64 pointers
|
||||
USBHS_USBCMD_PSE;
|
||||
|
||||
USBHS_PORTSC1 |= USBHS_PORTSC_PP;
|
||||
//USBHS_PORTSC1 |= USBHS_PORTSC_PFSC; // force 12 Mbit/sec
|
||||
//USBHS_PORTSC1 |= USBHS_PORTSC_PHCD; // phy off
|
||||
}
|
||||
|
||||
void port_status()
|
||||
@ -77,12 +101,14 @@ void port_status()
|
||||
} else {
|
||||
Serial.print("off ");
|
||||
}
|
||||
|
||||
if (n & USBHS_PORTSC_PHCD) {
|
||||
Serial.print("phyoff ");
|
||||
}
|
||||
if (n & USBHS_PORTSC_PE) {
|
||||
if (USBHS_PORTSC_SUSP) {
|
||||
if (n & USBHS_PORTSC_SUSP) {
|
||||
Serial.print("suspend ");
|
||||
} else {
|
||||
Serial.print("enable "); // not working... why?
|
||||
Serial.print("enable ");
|
||||
}
|
||||
} else {
|
||||
Serial.print("disable ");
|
||||
@ -101,10 +127,24 @@ void port_status()
|
||||
Serial.print("overcurrent ");
|
||||
}
|
||||
if (n & USBHS_PORTSC_CCS) {
|
||||
Serial.print("connected");
|
||||
Serial.print("connected ");
|
||||
} else {
|
||||
Serial.print("not-connected");
|
||||
Serial.print("not-connected ");
|
||||
}
|
||||
// print info about the EHCI status
|
||||
Serial.print(" run=");
|
||||
Serial.print(USBHS_USBCMD & 1); // running mode
|
||||
Serial.print(",halt=");
|
||||
Serial.print((USBHS_USBSTS >> 12) & 1); // halted mode
|
||||
Serial.print(",err=");
|
||||
Serial.print((USBHS_USBSTS >> 4) & 1); // error encountered!
|
||||
Serial.print(",asyn=");
|
||||
Serial.print((USBHS_USBSTS >> 15) & 1); // running the async schedule
|
||||
Serial.print(",per=");
|
||||
Serial.print((USBHS_USBSTS >> 14) & 1); // running the periodic schedule
|
||||
Serial.print(",index=");
|
||||
Serial.print(USBHS_FRINDEX); // periodic index
|
||||
|
||||
Serial.println();
|
||||
}
|
||||
|
||||
@ -120,15 +160,17 @@ void loop()
|
||||
Serial.println("Plug in device...");
|
||||
digitalWrite(32, HIGH); // connect device
|
||||
}
|
||||
if (count == 6) {
|
||||
if (count == 5) {
|
||||
Serial.println("Initiate Reset Sequence...");
|
||||
USBHS_PORTSC1 |= USBHS_PORTSC_PR;
|
||||
}
|
||||
if (count == 16) {
|
||||
if (count == 15) {
|
||||
Serial.println("End Reset Sequence...");
|
||||
USBHS_PORTSC1 &= ~USBHS_PORTSC_PR;
|
||||
}
|
||||
|
||||
if (count > 5000) {
|
||||
while (1) ; // stop here
|
||||
}
|
||||
}
|
||||
|
||||
void print(const char *s)
|
||||
|
Loading…
Reference in New Issue
Block a user