mirror of https://github.com/raphnet/4nes4snes
271 lines
12 KiB
C
271 lines
12 KiB
C
/* Name: usbconfig.h
|
|
* Project: AVR USB driver
|
|
* Author: Christian Starkjohann
|
|
* Creation Date: 2005-04-01
|
|
* Tabsize: 4
|
|
* Copyright: (c) 2005 by OBJECTIVE DEVELOPMENT Software GmbH
|
|
* License: GNU GPL v2 (see License.txt) or proprietary (CommercialLicense.txt)
|
|
* This Revision: $Id: usbconfig.h,v 1.13 2016-06-06 02:42:27 cvs Exp $
|
|
*/
|
|
|
|
#ifndef __usbconfig_h_included__
|
|
#define __usbconfig_h_included__
|
|
|
|
/*
|
|
General Description:
|
|
This file is an example configuration (with inline documentation) for the USB
|
|
driver. It configures AVR-USB for an ATMega8 with USB D+ connected to Port D
|
|
bit 2 (which is also hardware interrupt 0) and USB D- to Port D bit 0. You may
|
|
wire the lines to any other port, as long as D+ is also wired to INT0.
|
|
To create your own usbconfig.h file, copy this file to the directory
|
|
containing "usbdrv" (that is your project firmware source directory) and
|
|
rename it to "usbconfig.h". Then edit it accordingly.
|
|
*/
|
|
|
|
/* ---------------------------- Hardware Config ---------------------------- */
|
|
|
|
#define USB_CFG_IOPORTNAME D
|
|
/* This is the port where the USB bus is connected. When you configure it to
|
|
* "B", the registers PORTB, PINB and DDRB will be used.
|
|
*/
|
|
#define USB_CFG_DMINUS_BIT 0
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D- line is connected.
|
|
* This may be any bit in the port.
|
|
*/
|
|
#define USB_CFG_DPLUS_BIT 2
|
|
/* This is the bit number in USB_CFG_IOPORT where the USB D+ line is connected.
|
|
* This may be any bit in the port. Please note that D+ must also be connected
|
|
* to interrupt pin INT0!
|
|
*/
|
|
#define USB_CFG_CLOCK_KHZ (F_CPU/1000)
|
|
/* Clock rate of the AVR in MHz. Legal values are 12000, 15000, 16000 or 16500.
|
|
* The 16.5 MHz version of the code requires no crystal, it tolerates +/- 1%
|
|
* deviation from the nominal frequency. All other rates require a precision
|
|
* of 2000 ppm and thus a crystal!
|
|
* Default if not specified: 12 MHz
|
|
*/
|
|
|
|
/* ----------------------- Optional Hardware Config ------------------------ */
|
|
|
|
/* #define USB_CFG_PULLUP_IOPORTNAME D */
|
|
/* If you connect the 1.5k pullup resistor from D- to a port pin instead of
|
|
* V+, you can connect and disconnect the device from firmware by calling
|
|
* the macros usbDeviceConnect() and usbDeviceDisconnect() (see usbdrv.h).
|
|
* This constant defines the port on which the pullup resistor is connected.
|
|
*/
|
|
/* #define USB_CFG_PULLUP_BIT 4 */
|
|
/* This constant defines the bit number in USB_CFG_PULLUP_IOPORT (defined
|
|
* above) where the 1.5k pullup resistor is connected. See description
|
|
* above for details.
|
|
*/
|
|
|
|
/* --------------------------- Functional Range ---------------------------- */
|
|
|
|
#define USB_CFG_HAVE_INTRIN_ENDPOINT 1
|
|
/* Define this to 1 if you want to compile a version with two endpoints: The
|
|
* default control endpoint 0 and an interrupt-in endpoint 1.
|
|
*/
|
|
#define USB_CFG_HAVE_INTRIN_ENDPOINT3 0
|
|
/* Define this to 1 if you want to compile a version with three endpoints: The
|
|
* default control endpoint 0, an interrupt-in endpoint 1 and an interrupt-in
|
|
* endpoint 3. You must also enable endpoint 1 above.
|
|
*/
|
|
/* #define USB_INITIAL_DATATOKEN USBPID_DATA0 */
|
|
/* The above macro defines the startup condition for data toggling on the
|
|
* interrupt/bulk endpoints 1 and 3. Defaults to USBPID_DATA0.
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_HALT 0
|
|
/* Define this to 1 if you also want to implement the ENDPOINT_HALT feature
|
|
* for endpoint 1 (interrupt endpoint). Although you may not need this feature,
|
|
* it is required by the standard. We have made it a config option because it
|
|
* bloats the code considerably.
|
|
*/
|
|
#define USB_CFG_INTR_POLL_INTERVAL 10
|
|
/* If you compile a version with endpoint 1 (interrupt-in), this is the poll
|
|
* interval. The value is in milliseconds and must not be less than 10 ms for
|
|
* low speed devices.
|
|
*/
|
|
#define USB_CFG_IS_SELF_POWERED 0
|
|
/* Define this to 1 if the device has its own power supply. Set it to 0 if the
|
|
* device is powered from the USB bus.
|
|
*/
|
|
#define USB_CFG_MAX_BUS_POWER 100
|
|
/* Set this variable to the maximum USB bus power consumption of your device.
|
|
* The value is in milliamperes. [It will be divided by two since USB
|
|
* communicates power requirements in units of 2 mA.]
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_FN_WRITE 0
|
|
/* Set this to 1 if you want usbFunctionWrite() to be called for control-out
|
|
* transfers. Set it to 0 if you don't need it and want to save a couple of
|
|
* bytes.
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_FN_READ 0
|
|
/* Set this to 1 if you need to send control replies which are generated
|
|
* "on the fly" when usbFunctionRead() is called. If you only want to send
|
|
* data from a static buffer, set it to 0 and return the data from
|
|
* usbFunctionSetup(). This saves a couple of bytes.
|
|
*/
|
|
#define USB_CFG_IMPLEMENT_FN_WRITEOUT 0
|
|
/* Define this to 1 if you want to use interrupt-out (or bulk out) endpoint 1.
|
|
* You must implement the function usbFunctionWriteOut() which receives all
|
|
* interrupt/bulk data sent to endpoint 1.
|
|
*/
|
|
#define USB_CFG_HAVE_FLOWCONTROL 0
|
|
/* Define this to 1 if you want flowcontrol over USB data. See the definition
|
|
* of the macros usbDisableAllRequests() and usbEnableAllRequests() in
|
|
* usbdrv.h.
|
|
*/
|
|
/* #define USB_RX_USER_HOOK(data, len) if(usbRxToken == (uchar)USBPID_SETUP) blinkLED(); */
|
|
/* This macro is a hook if you want to do unconventional things. If it is
|
|
* defined, it's inserted at the beginning of received message processing.
|
|
* If you eat the received message and don't want default processing to
|
|
* proceed, do a return after doing your things. One possible application
|
|
* (besides debugging) is to flash a status LED on each packet.
|
|
*/
|
|
#define USB_COUNT_SOF 0
|
|
/* define this macro to 1 if you need the global variable "usbSofCount" which
|
|
* counts SOF packets.
|
|
*/
|
|
|
|
/* -------------------------- Device Description --------------------------- */
|
|
|
|
/* This is the Dracal technologies inc. (Raphnet technologies) VID */
|
|
#define USB_CFG_VENDOR_ID 0x9B, 0x28
|
|
#define USB_CFG_DEVICE_ID 0x03, 0x00
|
|
|
|
|
|
#define USB_CFG_DEVICE_VERSION 0x05, 0x01
|
|
/* Version number of the device: Minor number first, then major number.
|
|
*/
|
|
#define USB_CFG_VENDOR_NAME 'r', 'a', 'p', 'h', 'n', 'e', 't', '.', 'n', 'e', 't'
|
|
#define USB_CFG_VENDOR_NAME_LEN 11
|
|
/* These two values define the vendor name returned by the USB device. The name
|
|
* must be given as a list of characters under single quotes. The characters
|
|
* are interpreted as Unicode (UTF-16) entities.
|
|
* If you don't want a vendor name string, undefine these macros.
|
|
* ALWAYS define a vendor name containing your Internet domain name if you use
|
|
* obdev's free shared VID/PID pair. See the file USBID-License.txt for
|
|
* details.
|
|
*/
|
|
/*
|
|
#define USB_CFG_DEVICE_NAME '(', 'S', ')', 'N', 'E', 'S', '/', \
|
|
'A', 't', 'a', 'r', 'i', '_', 'U', 'S', 'B'
|
|
#define USB_CFG_DEVICE_NAME_LEN 16*/
|
|
/* Same as above for the device name. If you don't want a device name, undefine
|
|
* the macros. See the file USBID-License.txt before you assign a name if you
|
|
* use a shared VID/PID.
|
|
*/
|
|
//#define USB_CFG_SERIAL_NUMBER 'N', 'o', 'n', 'e'
|
|
#define USB_CFG_SERIAL_NUMBER_LEN 4
|
|
/* Same as above for the serial number. If you don't want a serial number,
|
|
* undefine the macros.
|
|
* It may be useful to provide the serial number through other means than at
|
|
* compile time. See the section about descriptor properties below for how
|
|
* to fine tune control over USB descriptors such as the string descriptor
|
|
* for the serial number.
|
|
*/
|
|
#define USB_CFG_DEVICE_CLASS 0
|
|
#define USB_CFG_DEVICE_SUBCLASS 0
|
|
/* See USB specification if you want to conform to an existing device class.
|
|
*/
|
|
#define USB_CFG_INTERFACE_CLASS 3 /* HID */
|
|
#define USB_CFG_INTERFACE_SUBCLASS 0
|
|
#define USB_CFG_INTERFACE_PROTOCOL 0
|
|
/* See USB specification if you want to conform to an existing device class or
|
|
* protocol.
|
|
* This template defines a HID class device. If you implement a vendor class
|
|
* device, set USB_CFG_INTERFACE_CLASS to 0 and USB_CFG_DEVICE_CLASS to 0xff.
|
|
*/
|
|
#define USB_CFG_HID_REPORT_DESCRIPTOR_LENGTH 0 /* total length of report descriptor */
|
|
/* Define this to the length of the HID report descriptor, if you implement
|
|
* an HID device. Otherwise don't define it or define it to 0.
|
|
* Since this template defines a HID device, it must also specify a HID
|
|
* report descriptor length. You must add a PROGMEM character array named
|
|
* "usbHidReportDescriptor" to your code which contains the report descriptor.
|
|
* Don't forget to keep the array and this define in sync!
|
|
*/
|
|
|
|
/* #define USB_PUBLIC static */
|
|
/* Use the define above if you #include usbdrv.c instead of linking against it.
|
|
* This technique saves a couple of bytes in flash memory.
|
|
*/
|
|
|
|
/* ------------------- Fine Control over USB Descriptors ------------------- */
|
|
/* If you don't want to use the driver's default USB descriptors, you can
|
|
* provide our own. These can be provided as (1) fixed length static data in
|
|
* flash memory, (2) fixed length static data in RAM or (3) dynamically at
|
|
* runtime in the function usbFunctionDescriptor(). See usbdrv.h for more
|
|
* information about this function.
|
|
* Descriptor handling is configured through the descriptor's properties. If
|
|
* no properties are defined or if they are 0, the default descriptor is used.
|
|
* Possible properties are:
|
|
* + USB_PROP_IS_DYNAMIC: The data for the descriptor should be fetched
|
|
* at runtime via usbFunctionDescriptor().
|
|
* + USB_PROP_IS_RAM: The data returned by usbFunctionDescriptor() or found
|
|
* in static memory is in RAM, not in flash memory.
|
|
* + USB_PROP_LENGTH(len): If the data is in static memory (RAM or flash),
|
|
* the driver must know the descriptor's length. The descriptor itself is
|
|
* found at the address of a well known identifier (see below).
|
|
* List of static descriptor names (must be declared PROGMEM if in flash):
|
|
* char usbDescriptorDevice[];
|
|
* char usbDescriptorConfiguration[];
|
|
* char usbDescriptorHidReport[];
|
|
* char usbDescriptorString0[];
|
|
* int usbDescriptorStringVendor[];
|
|
* int usbDescriptorStringDevice[];
|
|
* int usbDescriptorStringSerialNumber[];
|
|
* Other descriptors can't be provided statically, they must be provided
|
|
* dynamically at runtime.
|
|
*
|
|
* Descriptor properties are or-ed or added together, e.g.:
|
|
* #define USB_CFG_DESCR_PROPS_DEVICE (USB_PROP_IS_RAM | USB_PROP_LENGTH(18))
|
|
*
|
|
* The following descriptors are defined:
|
|
* USB_CFG_DESCR_PROPS_DEVICE
|
|
* USB_CFG_DESCR_PROPS_CONFIGURATION
|
|
* USB_CFG_DESCR_PROPS_STRINGS
|
|
* USB_CFG_DESCR_PROPS_STRING_0
|
|
* USB_CFG_DESCR_PROPS_STRING_VENDOR
|
|
* USB_CFG_DESCR_PROPS_STRING_PRODUCT
|
|
* USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER
|
|
* USB_CFG_DESCR_PROPS_HID
|
|
* USB_CFG_DESCR_PROPS_HID_REPORT
|
|
* USB_CFG_DESCR_PROPS_UNKNOWN (for all descriptors not handled by the driver)
|
|
*
|
|
*/
|
|
|
|
#define USB_CFG_DESCR_PROPS_DEVICE USB_PROP_IS_DYNAMIC
|
|
#define USB_CFG_DESCR_PROPS_CONFIGURATION (USB_PROP_IS_DYNAMIC | USB_PROP_IS_RAM)
|
|
#define USB_CFG_DESCR_PROPS_STRINGS 0
|
|
#define USB_CFG_DESCR_PROPS_STRING_0 0
|
|
#define USB_CFG_DESCR_PROPS_STRING_VENDOR 0
|
|
|
|
#define DEVICE_STRING_LENGTH 14
|
|
#define DEFAULT_PROD_STRING '4','n','e','s','4','s','n','e','s',' ','v','1','.','5'
|
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_PRODUCT (USB_PROP_LENGTH(((DEVICE_STRING_LENGTH+2)*2)) | USB_PROP_IS_RAM)
|
|
|
|
#define USB_CFG_DESCR_PROPS_STRING_SERIAL_NUMBER USB_PROP_LENGTH((6*2))
|
|
#define USB_CFG_DESCR_PROPS_HID 0
|
|
#define USB_CFG_DESCR_PROPS_HID_REPORT USB_PROP_IS_DYNAMIC
|
|
#define USB_CFG_DESCR_PROPS_UNKNOWN 0
|
|
|
|
/* ----------------------- Optional MCU Description ------------------------ */
|
|
|
|
/* The following configurations have working defaults in usbdrv.h. You
|
|
* usually don't need to set them explicitly. Only if you want to run
|
|
* the driver on a device which is not yet supported or with a compiler
|
|
* which is not fully supported (such as IAR C) or if you use a differnt
|
|
* interrupt than INT0, you may have to define some of these.
|
|
*/
|
|
/* #define USB_INTR_CFG MCUCR */
|
|
/* #define USB_INTR_CFG_SET ((1 << ISC00) | (1 << ISC01)) */
|
|
/* #define USB_INTR_CFG_CLR 0 */
|
|
/* #define USB_INTR_ENABLE GIMSK */
|
|
/* #define USB_INTR_ENABLE_BIT INT0 */
|
|
/* #define USB_INTR_PENDING GIFR */
|
|
/* #define USB_INTR_PENDING_BIT INTF0 */
|
|
/* #define USB_INTR_VECTOR SIG_INTERRUPT0 */
|
|
|
|
#endif /* __usbconfig_h_included__ */
|